Categories
Contact Us

Email:jp004@jp-balancer.com

Tel: +86-21-39972151

Fax:+86-21-39972968

QQ: 2881090407

WhatsApp: +86-13817256095

Skype:shjpphj

Website: www.jp-balancer.com


Shanghai Jianping Dynamic Balancing Machine Manufacturing Co., Ltd.

Add: No.2151,Panchuan Road,Luojing Town,Baoshan District,Shanghai. China.


Service Hotline
+86-21-39972151

News

Home > NewsContent

Horizontal Balancing Machine A Rotor With A Shaft Or A Processable Shaft

Horizontal balancing machine ----- is the balance of the rotor rotation axis in the balance on the horizontal machine, in general, with a shaft or can be equipped with the process of the shaft, such as motor rotor, machine tool spindle, drum, fan , Steam turbine, supercharger rotor, etc., are applicable to horizontal balancing machine. Mainly used in large-scale motor rotor, blower, centrifugal impeller, dryer, drum and other rotating parts of the balance check.

Trouble Cause and Elimination of Horizontal Balancing Machine

There are many factors that cause the balancing machine to fail or fail to achieve equilibrium. Some of these factors are the reason for balancing the workpiece, and the reason for the machine itself or the electrical system. So as long as a link is not normal will inevitably affect the balance of the workpiece, such as targeted analysis of these phenomena in order to help us correctly distinguish and determine the reasons for the emergence of various circumstances, and then take effective measures to reduce or eliminate these The Influence of Unfavorable Factors on Workpiece Balance.

The impact of the workpiece

Correcting the workpiece imbalance requires more than the balance machine itself, the minimum reachable residual unbalance, that is, the balance of the balance of precision can not meet the requirements of the workpiece balance.

The roundness of the journal itself is not good and the surface roughness is too low.

The rigidity of the workpiece itself is poor, resulting in a mass offset during deformation at high speeds, or where the workpiece itself has an immobilized part moving or loosening in a rotating state.

The balance of the rotor in the actual use of the obvious vibration will occur, which is not caused by the imbalance of the rotor itself, but because the rotor support journal into an oval or rotor structure on the existence of differences in stiffness caused by the high harmonics , The vibration caused by electromagnetic excitation, the influence of the blade vane on the generation of the vortex in the rotation process, the resonance of the system, and so on.

Due to the frequent activation of other equipment connected to the grid caused by power fluctuations and noise or due to the support roller and the rotor shaft diameter similar to the two produced by the beat frequency interference. The difference between the wheel diameter and the workpiece journal size should be greater than 20%.

Due to the calibration of the journal without the journal rotor and the use of the core itself is not balanced or the mandrel installation and support at the coaxial degree of error, and the spindle and the rotor with the gap between the error caused by the balance of the rotor in the repeated loading school When used or when there is a large imbalance.

The actual working state of the workpiece rotor and the state of the balance check are inconsistent.

When the unbalance amount of the workpiece rotor is corrected, the center position of the aggravated or de-gravity is offset from the correction position displayed by the balancing machine.

Balance the impact of the machine

1. Left and right support at the level of the rotor around the movement or journal plane and support the Department of rubbing.

2. The support block is seriously worn or the roller beats increase.

3. Supports dirt, no lubricants.

4. Install the balance of the foundation does not meet the requirements of the bottom of the joint surface is not pad, the anchor bolts are not fastened, or on the floor, causing resonance.

5. The output signal of the sensor is not normal.

6. The fastening screws at the parts that can be moved on the support frame are not tightened.

7. Transmission does not meet the requirements, there are obvious seams.

8. Balancing machine photoelectric head is not positive reflective paper, photoelectric head mirror blurred, optical head position deviation caused by angular offset.